Maker Pro
Maker Pro

PSPICE A/D simulation problem

R

RsK

Hi anyone can see the pspice file and please tell me how to remove the
error it displays while simulation?

regards,
rizwan

*
..MODEL QBC337-25 NPN(
+ IS = 4.13E-14
+ NF = 0.9822
+ ISE = 3.534E-15
+ NE = 1.35
+ BF = 292.4
+ IKF = 0.9
+ VAF = 145.7
+ NR = 0.982
+ ISC = 1.957E-13
+ NC = 1.3
+ BR = 23.68
+ IKR = 0.1
+ VAR = 20
+ RB = 60
+ IRB = 0.0002
+ RBM = 8
+ RE = 0.1129
+ RC = 0.25
+ XTB = 0
+ EG = 1.11
+ XTI = 3
+ CJE = 3.799E-11
+ VJE = 0.6752
+ MJE = 0.3488
+ TF = 5.4E-10
+ XTF = 4
+ VTF = 4.448
+ ITF = 0.665
+ PTF = 90
+ CJC = 1.355E-11
+ VJC = 0.3523
+ MJC = 0.3831
+ XCJC = 0.455
+ TR = 3E-08
+ CJS = 0
+ VJS = 0.75
+ MJS = 0.333
+ FC = 0.643)
*
*Resistors
*
R1 2 4 56k
R2 2 0 22k
RB 2 3 180
RC 4 5 5.1k
RE 6 0 3.3k
* Load
RL 8 0 1k
CL 5 8 10u
*
*Capacitors
*
C1 1 2 330n
CC 3 5 470p
CE 6 0 220u
VCC 4 0 15
*
..AC DEC 10 10 100k
..PROBE
..END
 
J

Jim Thompson

Top posting to be as big an annoyance as possible ;-)

(1) You show a model of an NPN. But there is no NPN in the netlist.

(2) What does the error message say?

Hi anyone can see the pspice file and please tell me how to remove the
error it displays while simulation?

regards,
rizwan

*
.MODEL QBC337-25 NPN(
+ IS = 4.13E-14
+ NF = 0.9822
+ ISE = 3.534E-15
+ NE = 1.35
+ BF = 292.4
+ IKF = 0.9
+ VAF = 145.7
+ NR = 0.982
+ ISC = 1.957E-13
+ NC = 1.3
+ BR = 23.68
+ IKR = 0.1
+ VAR = 20
+ RB = 60
+ IRB = 0.0002
+ RBM = 8
+ RE = 0.1129
+ RC = 0.25
+ XTB = 0
+ EG = 1.11
+ XTI = 3
+ CJE = 3.799E-11
+ VJE = 0.6752
+ MJE = 0.3488
+ TF = 5.4E-10
+ XTF = 4
+ VTF = 4.448
+ ITF = 0.665
+ PTF = 90
+ CJC = 1.355E-11
+ VJC = 0.3523
+ MJC = 0.3831
+ XCJC = 0.455
+ TR = 3E-08
+ CJS = 0
+ VJS = 0.75
+ MJS = 0.333
+ FC = 0.643)
*
*Resistors
*
R1 2 4 56k
R2 2 0 22k
RB 2 3 180
RC 4 5 5.1k
RE 6 0 3.3k
* Load
RL 8 0 1k
CL 5 8 10u
*
*Capacitors
*
C1 1 2 330n
CC 3 5 470p
CE 6 0 220u
VCC 4 0 15
*
.AC DEC 10 10 100k
.PROBE
.END


...Jim Thompson
 
H

Helmut Sennewald

RsK said:
Hi anyone can see the pspice file and please tell me how to remove the
error it displays while simulation?

regards,
rizwan

Hello rizwan,

I don't know what PSPICE reports, but the error report from
LTspice is crystal clear if you know SPICE.

WARNING: Node 1 is floating.
WARNING: Less than two connections to node 1. This node is used by C1.
---> one pin of C1 is not connected

No AC stimulus found:
Set the value of a current or voltage source to "AC 1."
to make it behave as a signal generator for AC analysis.
---> An AC-analysis requires at least one voltage source with an "AC"
definiton.


This doesn't matter, but why do you have a transistor model when you don't
use a transistor?

Best regards,
Helmut
 
Top